Primo Reset Glitch Hack

**Titty** · 25-01-12

No problem, you must connect two GRN point: one for xilinx and one for Nand reader

Where did you installed?

**xbox3602000** · 25-01-12

Originariamente Scritto da Titty

No problem, you must connect two GRN point: one for xilinx and one for Nand reader

Where did you installed?

Ma i due GND servono anche se utilizzo l' X360 SQUIRT SLAVE PROGRAMMER SPI NAND + JTAG USB 2.0 ??

Da quanto ho capito con il programmer posso programmare il chip fuori dalla mother board.

**Titty** · 25-01-12

Ma cosa centra la slave con il montaggio... una massa serve per lo Xilinx (per farlo andare sulla console) e una per il Nand reader... sono 2 cose distinte... non mescoliamo capre e cavoli... La slave è la slave che centra con il montaggio su scheda madre?

**milsey** · 25-01-12

Ho usato LPT per leggere / scrivere il mio Nand
Ho usato LPT per programmare il Squirt
Ora devo solo la Squirt collegato con il POSTBIT, SDA, CPU_RST, SCL, CLK, GND (accanto a CPU_RST) e 3,3 V a LPT_VCC.
Ho ancora bisogno di entrambi GND collegato solo per RGH, se faccio allora è lì che sto andando male! 2 giorni ho trascorrere cambiare condensatori, la tensione, filo, lunghezza del cavo!

**xbox3602000** · 25-01-12

Originariamente Scritto da Titty

Ma cosa centra la slave con il montaggio... una massa serve per lo Xilinx (per farlo andare sulla console) e una per il Nand reader... sono 2 cose distinte... non mescoliamo capre e cavoli... La slave è la slave che centra con il montaggio su scheda madre?

avevo capito che la doppia GND era sulla basetta dello Xilinx. E' ovvio che se ho 2 'basette' una per lo Xilinx e l'altra per il Nand reader dovranno avere una GND ciascuna

**Titty** · 25-01-12

On what motherboard you have installed the Squirt?

You can post photos of installation?

**Luke69** · 25-01-12

Originariamente Scritto da xbox3602000

avevo capito che la doppia GND era sulla basetta dello Xilinx. E' ovvio che se ho 2 'basette' una per lo Xilinx e l'altra per il Nand reader dovranno avere una GND ciascuna

Il programmer è integrato insieme allo xilinx sulla stessa basetta, lo slave serve solo per interfacciarsi con il pic e lo xilinx, non ci si deve saldare sopra...comunque c'è una guida...

**milsey** · 25-01-12

Originariamente Scritto da Titty

On what motherboard you have installed the Squirt?

You can post photos of installation?

I am at work, so I can't post photo's now. I had a few problems in the beginning (using wrong stiff single core wire), and I had to apply some fixes

POSTOUT - I pulled the solder off and couldn't get it to stick again so I had to use alternate point on top of board ([url]http://img18.imageshack.us/img18/7372/postalt.jpg[/url])

CPU_RST - Same story, I had to join R4N4 ([url]http://img546.imageshack.us/img546/6957/cpualt.jpg[/url]) to C5R17 and use C5R17 as CPU_RST as in picture ([url=http://imageshack.us/photo/my-images/843/050vgf.jpg/]ImageShack® - Online Photo and Video Hosting[/url])

STBY_CLK - I wrecked that too... burned the 33ohm resistor, which I replaced from a old Xbox DVD drive board. The alternate point under the board, i pulled the solder out of that too so I can't use that.

**milsey** · 25-01-12

Originariamente Scritto da Titty

On what motherboard you have installed the Squirt?

You can post photos of installation?

I had a few problems in the beginning (using wrong stiff single core wire), and I had to apply some fixes

POSTOUT - I pulled the solder off and couldn't get it to stick again so I had to use alternate point on top of board.
CPU_RST - Same story, I had to join R4N4 to C5R17 ([url=http://s785.photobucket.com/albums/yy134/djtravisc/xbox/?action=view&current=photo32.jpg]xbox :: photo32.jpg picture by djtravisc - Photobucket[/url]) and use C5R17 as CPU_RST as in picture ([url]http://i785.photobucket.com/albums/yy134/djtravisc/xbox/photo12.jpg[/url])

STBY_CLK - I wrecked that too... burned the 33ohm resistor, which I replaced from a old Xbox DVD drive board [url=http://s785.photobucket.com/albums/yy134/djtravisc/xbox/?action=view&current=photo13.jpg]xbox :: photo13.jpg picture by djtravisc - Photobucket[/url]. The alternate point under the board, i pulled the solder out of that too so I can't use that.

This is what my coil looks like [url]http://i785.photobucket.com/albums/yy134/djtravisc/xbox/photo3.jpg[/url]

Jtag connections [url=http://s785.photobucket.com/albums/yy134/djtravisc/xbox/?action=view&current=photo2.jpg]xbox :: photo2.jpg picture by djtravisc - Photobucket[/url]

Squirt connectionx [url=http://s785.photobucket.com/albums/yy134/djtravisc/xbox/?action=view&current=photo4.jpg]xbox :: photo4.jpg picture by djtravisc - Photobucket[/url]

**milsey** · 25-01-12

Can anyone help?

**Vola** · 26-01-12

Hi, your soldering looks quite bad, use flux and a lower temperature since you have lost some pads....
It's also better to move away the chip from the motherboard coils, to avoid interferences

**milsey** · 26-01-12

My soldering is quite bad!!! But to be fair it's slowly got worse looking as I've changed wire so many times.

**milsey** · 27-01-12

Do I need to be on a specific dash? I'm not on new one yet...

**Titty** · 27-01-12

Originariamente Scritto da milsey

Do I need to be on a specific dash? I'm not on new one yet...

No, you can use any kernel

**milsey** · 28-02-12

No matter what I try it just won't glitch!! Ive tried changing the length of CPU_RST, I've changed the wire type and gauge 26-30. I have also tried the new alternate trinity timings. Maybe my squirt is broken, my Xbox is useless without getting it glitched, I lost the DVD KEY. Don't know what else to do. Squirt support is shocking, wish I went for more expensive TX coolrunner.

**Titty** · 29-02-12

You can post pictures again of installation?
Do not use for CPU_RST wire 30cm and install the trinity1.1.sfv and last set the capacitor at 270pF

**milsey** · 29-02-12

Are the pictures above not good enough? I ordered the slave board to make my life easier. When that arrives I will update to trinity 1.1. Is 270pf the best to use for Trinity? It says on Squirt website that 220 is most used?

**Titty** · 29-02-12

Have you redone the solderings?
The position of the chip should be changed ([url]http://www.consoleopen.com/forum/images/tutorial/Xbox360/INSTALL_SQUIRT/pag1.h1212.jpg[/url])

**milsey** · 02-03-12

I have redone the soldering on numerous occasions.

Where should I put the chip?

I tried loading the squirt coolrunner with trinity.1.1.svf taken from bitstream software off Squirt site and still no boot.

Today I received my squirt slave board but it won't read the NAND connected through squirt coolrunner, it says bad NAND connection. I've checked it over a few times but still not working. Could that be a hint that something isn't right on my squirt coolrunner?