www.dedoshop.com
Risultati da 1 a 19 di 19
Like Tree5Likes
  • 2 Post By The Pusher
  • 2 Post By lucard
  • 1 Post By Pa0l0ne

Discussione: problema nand

  1. #1
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73

    problema nand

    ciao a tutti.
    Ho un problema con la nand di una trinity.
    ho fatto rgh e sembra tutto funzionare bene . ho montato un coolrunner rev d jp open 1-2 e selettore su phat e fili in dotazione.
    xell parte in 40 secondi 1 minuto circa.
    flasho il freebot e boota in 20 secondi(xell e' più lento)
    e la console si blocca sulla scritt axbox 360
    la nand mi da bad block in area 0x14e.
    puo' essere questo? di solito j runner mi remappa i bad block e non ho mai avuto problemi
    o puo essere un errore dovuto al cpu rst?e' arrotolato alle x clamp
    ovviamente se torno alla nand stock tutto funziona alla perfezione
    grazie in anticipo a chi mi sapra' rispondere
    Ultima modifica di lucard; 15-05-15 alle 23: 52

  2. #2
    Vip Member L'avatar di chojin
    Data Registrazione
    Aug 2011
    Località
    Arezzo
    Messaggi
    1,239
    prova a creare freeboot con autogg invece che con jrunner

  3. #3
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    fatto ma non funziona.
    sempre lo stesso blocco al logo.
    ho letto in giro che tanti staccano l hard disk con questo problema, ma questa trinity ha la memoria interna da 4 gb
    se la rimettessi stock visto che funziona originale e provassi a formattare la memoria interna?
    ho provato a creare il freebot senza dash launch e il suo ini ma niente

  4. #4
    Dolo-miticusss L'avatar di Babilozzo
    Data Registrazione
    May 2012
    Località
    Marmolada, Dolomiti
    Messaggi
    4,279
    Prova a spuntare il flag nohdmi e nomobile di xebuild
    Esplora i link spaziali dei Tutorial RGH fatti con le mie manine Sante
    «L'abitudine e' in tutte le cose il miglior maestro.» -- Plinio il vecchio, "Storia naturale"

  5. #5
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    in auto gg nella menu xebuild trovo solo nohdmi
    Ultima modifica di lucard; 17-05-15 alle 21: 00

  6. #6
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    fatto dopo il boot si spegne la luce verde della xbox e le ventole continuano a girare e schermo nero
    usato j runner
    non devo rimappare la nand?
    mi da errore grave 0x14 quando flasho con rawflash

  7. #7
    Dolo-miticusss L'avatar di Babilozzo
    Data Registrazione
    May 2012
    Località
    Marmolada, Dolomiti
    Messaggi
    4,279
    Molto strano. Posta il log completo di xebuild che trovi nella cartella assieme all'updflash.bin....
    Posta foto delle saldature della tua installazione attuale semmai vorrai continuare la discussione.
    Sinceramente non so cosa intendi per errore grave cmq magari a qualcun'altro è già capitata una cosa simile e ti aiuta forse... se vuoi rimappare a mano puoi farlo non serve che chiedi il permesso.
    Esplora i link spaziali dei Tutorial RGH fatti con le mie manine Sante
    «L'abitudine e' in tutte le cose il miglior maestro.» -- Plinio il vecchio, "Storia naturale"

  8. #8
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    base path changed to C:\Users\Luca\Desktop\J-Runner\xeBuild
    ---- { Image Build Mode } ----
    building glitch2 image
    key on completion suppressed
    data directory overridden from command line to '17150\'
    per build directory overridden from command line to 'data\'
    file name overridden from command line to 'C:\Users\Luca\Desktop\J-Runner\\updflash.bin'

    ------ parsing user ini at 'data\options.ini' ------
    loading file...done!
    pre-parsing and sanitizing
    done!
    User options.ini loaded, 0x1a0 bytes in memory
    loading cpukey.txt from data\cpukey.txt
    CPU Key set to: blabla (weight:0x35 valid; ecd: valid)
    setting 1blkey from ini: 0xDD88AD0C9ED669E7B56794FB68563EFA
    1BL Key set to : 0xDD88AD0C9ED669E7B56794FB68563EFA sum: 0x983 (expects: 0x983)
    xex Key set to : 0x20B185A59D28FDC340583FBB0896BF91 sum: 0x800 (expects: 0x800)
    Using patchsmc option (ini file)

    ------ parsing ini at '17150\_glitch2.ini' ------
    ini version 17150

    ini: label [trinitybl] found
    found (1) 'cba_9188.bin' crc: 0x5a76752d
    found (2) 'cbb_9188.bin' crc: 0xfebb1074
    found (3) 'cd_9452.bin' crc: 0x455fa02c
    found (4) 'ce_1888.bin' crc: 0xff9b60df
    found (5) 'cf_17150.bin' crc: 0x0a774268
    found (6) 'cg_17150.bin' crc: 0xbe8ac817
    ini dictates dual CB for this model

    ini: label [flashfs] found
    found (1) 'aac.xexp' crc: 0x899d7c53
    found (2) 'bootanim.xex' crc: 0xe76c8e84
    found (3) 'createprofile.xex' crc: 0x76c0f2c7
    found (4) 'dash.xex' crc: 0xe1f07b1b
    found (5) 'deviceselector.xex' crc: 0x99aff203
    found (6) 'gamerprofile.xex' crc: 0x06185dc9
    found (7) 'hud.xex' crc: 0x9f8dade0
    found (8) 'huduiskin.xex' crc: 0xb186c353
    found (9) 'mfgbootlauncher.xex' crc: 0xcb0b86e3
    found (10) 'minimediaplayer.xex' crc: 0x81bb6500
    found (11) 'nomni.xexp' crc: 0x7adef6f6
    found (12) 'nomnifwk.xexp' crc: 0x6d7543f5
    found (13) 'nomnifwm.xexp' crc: 0xa8a27e56
    found (14) 'SegoeXbox-Light.xtt' crc: 0xe0ee6049
    found (15) 'signin.xex' crc: 0x6dd20623
    found (16) 'updater.xex' crc: 0x018dad7d
    found (17) 'vk.xex' crc: 0x3edc0dbb
    found (18) 'xam.xex' crc: 0x68767303
    found (19) 'xenonclatin.xtt' crc: 0xd5d17ff5
    found (20) 'xenonclatin.xttp' crc: 0x7a507ad1
    found (21) 'xenonjklatin.xtt' crc: 0xdde4a14c
    found (22) 'xenonjklatin.xttp' crc: 0xe2adddfb
    found (23) 'ximecore.xex' crc: 0x6f9e8b97
    found (24) 'ximedic.xex' crc: 0x1d992bfb
    found (25) 'ximedic.xexp' crc: 0x1a4863a4

    ini: label [security] found
    found (1) 'crl.bin' crc: 0x00000000
    found (2) 'dae.bin' crc: 0x00000000
    found (3) 'extended.bin' crc: 0x00000000
    found (4) 'fcrt.bin' crc: 0x00000000
    found (5) 'secdata.bin' crc: 0x00000000
    ------ ini parsing completed ------

    output name overridden to: C:\Users\Luca\Desktop\J-Runner\l\updflash.bin

    1BL RSA pub key file is not available, signature checks will not be performed
    PIRS RSA pub key file is not available, signature checks will not be performed
    MASTER RSA pub key file is not available, signature checks will not be performed

    ------ Checking data\nanddump.bin ------
    data\nanddump.bin file size: 0x1080000
    nanddump header checks passed OK!
    Loading NAND dump (0x1080000 bytes)...done!
    Detecting NAND controller type from dump data...
    NAND dump is from a small block machine
    NAND dump uses big block controller
    parsing dump into user and spare...
    bad block at 0x14e (raw offset 0x561c00), block ignored
    copying nanddump data from block 0x3fe to block 0x14e for file extraction integrity
    block 0x14e was remapped to block 0x3fe at remap instance 0
    copying nanddump data from block 0x3ff to block 0x14e for file extraction integrity
    block 0x14e was remapped to block 0x3ff, entering remap instance 2
    done!
    cleaning up stray remaps
    done!
    --remap summary--
    0: source: 0x014e dest: 0x03fe
    1: source: 0x014e dest: 0x03ff
    -----------------
    decrypting KeyVault at address 0x4000 of size 0x4000
    keyvault decrypted OK, will use if no kv.bin is provided
    decrypting SMC at address 0x1000 of size 0x3000
    SMC decrypted OK, will use if no external smc.bin is provided
    seeking smc config in dump...found at offset 0xf7c000! Using if no smc config is provided.
    CF slot 0 decrypted ok LDV 0x07 Pairing: 0x46c2bb
    CF slot 1 decrypted ok LDV 0x06 Pairing: 0x46c2bb
    setting LDV from image to 7
    setting pairing data from image to 0x46c2bb
    pairing set to: 46 c2 bb
    MobileB.dat found at block 0x114, page 0xc (page 0x228c), size 2048 (0x800) bytes
    MobileC.dat found at block 0x27, page 0x0 (page 0x4e0), size 512 (0x200) bytes
    MobileD.dat found at block 0x278, page 0x10 (page 0x4f10), size 2048 (0x800) bytes
    MobileE.dat found at block 0xdb, page 0x0 (page 0x1b60), size 2048 (0x800) bytes
    Statistics.settings found at page 0x7bc0, size 4096 (0x1000) bytes
    seeking FSRoot...fsroot found at block 0xdc, page 0x0 (page 0x1b80) raw offset 0x1b80
    seeking security files...
    crl.bin found in sector 0x129 size 0xa00...verified! Will use if external file not found.
    dae.bin found in sector 0x126 size 0x7090...verified! Will use if external file not found.
    extended.bin found in sector 0x10d size 0x4000...verified! Will use if external file not found.
    fcrt.bin found in sector 0x362 size 0x4000...pub key to verify signature is not available, skipping!
    verified! Will use if external file not found.
    secdata.bin found in sector 0x124 size 0x400...verified! Will use if external file not found.
    done!
    Writing initial header to flash image

    ------ loading system update container ------
    17150\su20076000_00000000 found, loading...done!
    Read 0xb37000 bytes to memory
    checking integrity...
    header seems valid, version 2.0.17150.0
    header hash is OK, checking content hashes...
    content hashes seem OK, everything looks good!
    extracted SUPD\xboxupd.bin (0x79fe0 bytes)
    decrypting SUPD\xboxupd.bin\CF_17150.bin (0x4560 bytes)...done!
    decrypting SUPD\xboxupd.bin\CG_17150.bin (0x75a80 bytes)...done!

    ------ Loading bootloaders and required security files ------
    reading data\smc.bin failed, using smc.bin from nand dump
    reset smc load address to 0x1000 size 0x3000
    reading data\kv.bin failed, using kv.bin from nand dump
    reading .\common\cba_9188.bin (0x1ac0 bytes)
    loaded cba_9188.bin, could not check signature rsa key not present!
    reading .\common\cbb_9188.bin (0x7800 bytes)
    reading .\common\cd_9452.bin (0x4f20 bytes)
    reading .\common\ce_1888.bin (0x5606a b pad 0x56070 b)
    reading data\xell-gggggg.bin (0x40000 bytes)
    extracted SUPD\xboxupd.bin\CF_17150.bin (0x4560 bytes)
    extracted SUPD\xboxupd.bin\CG_17150.bin (0x75a80 bytes)
    reading 17150\bin\patches_g2trinity.bin (0x910 bytes)
    reading data\smc_config.bin failed, using smc_config.bin from nand dump
    -------------------
    checking smc_config
    -------------------
    extracting config
    ------------------
    SMC config info:
    ------------------
    Target temps: Cpu: 82øC Gpu: 78øC Edram: 76øC
    Max temps : Cpu: 89øC Gpu: 82øC Edram: 82øC
    Cpu Fan : (auto)
    Gpu Fan : (auto)
    MAC Address : 7c:ed:8d:46:1c:43
    AVRegion : 0x00000300 (PAL50)
    GameRegion : 0x02fe (PAL/EU)
    DVDRegion : 2
    resetKey : DUUX
    ---------------------
    Checking for smc config data patches
    smc config was not patched
    ---------------------
    could not check signature of cba_9188.bin, 1BL RSA key not present!
    done!
    patch slot offset reset to: 0xb0000

    ------ Patching BLs and modifying patches ------
    Patching BLs...Done!

    ------ Patching boot reasons and options into flash header ------
    Patching header for xell power reason

    ------ Encrypting and finalizing bootloaders ------
    encoding smc.bin size 0x3000
    SMC checksum: f9c96639
    known clean SMC found, type: Trinity v5.1(3.01)
    patching SMC reset limit at offset: 0x13b3
    SMC reset limit patched successfully!
    encoding kv.bin size 0x4000
    decrypted keyvault has been set for reference
    Master RSA pub not available, not checking hash
    encoding cba_9188.bin size 0x1ac0
    encoding cbb_9188.bin size 0x7800
    CB 9188 seq 0x03010001 type: 0x03 cseq: 0x01 allow: 0x0001
    expected fuses:
    fuseset 00: C0FFFFFFFFFFFFFF
    fuseset 01: 0F0F0F0F0F0FF0F0 (retail slim)
    fuseset 02: F000000000000000 (sequence)
    fuseset 02: F000000000000000 (allow cseq 1)
    **dual CB flag detected!**
    encoding cd_9452.bin size 0x5290
    encoding ce_1888.bin size 0x56070
    encoding xell-gggggg.bin size 0x40000
    encoding cf_17150.bin size 0x4560
    encoding cg_17150.bin size 0x75a80
    encoding patches_g2trinity.bin size 0x544
    done!

    ------ Adding bootloaders to flash image ------
    adding smc.bin at raw offset 0x00001000 len 0x3000 (end 0x4000)
    adding kv.bin at raw offset 0x00004000 len 0x4000 (end 0x8000)
    adding cba_9188.bin at raw offset 0x00008000 len 0x1ac0 (end 0x9ac0)
    adding cbb_9188.bin at raw offset 0x00009ac0 len 0x7800 (end 0x112c0)
    adding cd_9452.bin at raw offset 0x000112c0 len 0x5290 (end 0x16550)
    adding ce_1888.bin at raw offset 0x00016550 len 0x56070 (end 0x6c5c0)
    adding xell-gggggg.bin at raw offset 0x00070000 len 0x40000 (end 0xb0000)
    adding cf_17150.bin at raw offset 0x000b0000 len 0x4560 (end 0xb4560)
    adding cg_17150.bin at raw offset 0x000b4560 len 0x75a80 (end 0xc0000, rest in fs)
    adding patches_g2trinity.bin at raw offset 0x000c0010 len 0x544 (end 0xc0554)
    Fixing up FS table...done!
    Writing zeropair CG patch slot overflow data to sysupdate.xexp1
    at raw offset 0xd0000 len 0x00069fe0 (end: 0x00139fe0)...done!

    ------ adding 25 firmware files ------
    extracted SUPD\aac.xexp (0x14000 bytes) (crc32: 0x899d7c53 ini: 0x899d7c53)
    adding as aac.xexp1 at raw offset 0x139fe0 len 0x00014000 (end 0x0014dfe0)
    extracted SUPD\bootanim.xex (0x61000 bytes) (crc32: 0xe76c8e84 ini: 0xe76c8e84)
    adding as bootanim.xex at raw offset 0x150000 len 0x00061000 (end 0x001b1000)
    extracted SUPD\createprofile.xex (0xc000 bytes) (crc32: 0x76c0f2c7 ini: 0x76c0f2c7)
    adding as createprofile.xex at raw offset 0x1b1000 len 0x0000c000 (end 0x001bd000)
    extracted SUPD\dash.xex (0x59b000 bytes) (crc32: 0xe1f07b1b ini: 0xe1f07b1b)
    adding as dash.xex at raw offset 0x1c0000 len 0x0059b000 (end 0x0075b000)
    extracted SUPD\deviceselector.xex (0xa000 bytes) (crc32: 0x99aff203 ini: 0x99aff203)
    adding as deviceselector.xex at raw offset 0x75b000 len 0x0000a000 (end 0x00765000)
    extracted SUPD\gamerprofile.xex (0x1b000 bytes) (crc32: 0x06185dc9 ini: 0x06185dc9)
    adding as gamerprofile.xex at raw offset 0x766000 len 0x0001b000 (end 0x00781000)
    extracted SUPD\hud.xex (0x1d000 bytes) (crc32: 0x9f8dade0 ini: 0x9f8dade0)
    adding as hud.xex at raw offset 0x783000 len 0x0001d000 (end 0x007a0000)
    extracted SUPD\huduiskin.xex (0x14000 bytes) (crc32: 0xb186c353 ini: 0xb186c353)
    adding as huduiskin.xex at raw offset 0x7a1000 len 0x00014000 (end 0x007b5000)
    extracted SUPD\mfgbootlauncher.xex (0x8000 bytes) (crc32: 0xcb0b86e3 ini: 0xcb0b86e3)
    adding as mfgbootlauncher.xex at raw offset 0x7b8000 len 0x00008000 (end 0x007c0000)
    extracted SUPD\minimediaplayer.xex (0xc000 bytes) (crc32: 0x81bb6500 ini: 0x81bb6500)
    adding as minimediaplayer.xex at raw offset 0x7c0000 len 0x0000c000 (end 0x007cc000)
    extracted SUPD\nomni.xexp (0xc800 bytes) (crc32: 0x7adef6f6 ini: 0x7adef6f6)
    adding as nomni.xexp1 at raw offset 0x7cc000 len 0x0000c800 (end 0x007d8800)
    extracted SUPD\nomnifwk.xexp (0x2000 bytes) (crc32: 0x6d7543f5 ini: 0x6d7543f5)
    adding as nomnifwk.xexp1 at raw offset 0x7d8800 len 0x00002000 (end 0x007da800)
    extracted SUPD\nomnifwm.xexp (0x5000 bytes) (crc32: 0xa8a27e56 ini: 0xa8a27e56)
    adding as nomnifwm.xexp1 at raw offset 0x7de000 len 0x00005000 (end 0x007e3000)
    extracted SUPD\SegoeXbox-Light.xtt (0x6000 bytes) (crc32: 0xe0ee6049 ini: 0xe0ee6049)
    adding as SegoeXbox-Light.xtt at raw offset 0x7e5000 len 0x00006000 (end 0x007eb000)
    extracted SUPD\signin.xex (0x19000 bytes) (crc32: 0x6dd20623 ini: 0x6dd20623)
    adding as signin.xex at raw offset 0x7ee000 len 0x00019000 (end 0x00807000)
    extracted SUPD\updater.xex (0x7000 bytes) (crc32: 0x018dad7d ini: 0x018dad7d)
    adding as updater.xex at raw offset 0x809000 len 0x00007000 (end 0x00810000)
    extracted SUPD\vk.xex (0xb000 bytes) (crc32: 0x3edc0dbb ini: 0x3edc0dbb)
    adding as vk.xex at raw offset 0x813000 len 0x0000b000 (end 0x0081e000)
    extracted SUPD\xam.xex (0x253000 bytes) (crc32: 0x68767303 ini: 0x68767303)
    adding as xam.xex at raw offset 0x81f000 len 0x00253000 (end 0x00a72000)
    extracted nanddump\xenonclatin.xtt (0x11b000 bytes) (crc32: 0xd5d17ff5 ini: 0xd5d17ff5)
    adding as xenonclatin.xtt at raw offset 0xa73000 len 0x0011b000 (end 0x00b8e000)
    extracted SUPD\xenonclatin.xttp (0x18000 bytes) (crc32: 0x7a507ad1 ini: 0x7a507ad1)
    adding as xenonclatin.xttp1 at raw offset 0xb8f000 len 0x00018000 (end 0x00ba7000)
    extracted nanddump\xenonjklatin.xtt (0x1a8000 bytes) (crc32: 0xdde4a14c ini: 0xdde4a14c)
    adding as xenonjklatin.xtt at raw offset 0xba8000 len 0x001a8000 (end 0x00d50000)
    extracted SUPD\xenonjklatin.xttp (0x7000 bytes) (crc32: 0xe2adddfb ini: 0xe2adddfb)
    adding as xenonjklatin.xttp1 at raw offset 0xd50000 len 0x00007000 (end 0x00d57000)
    extracted SUPD\ximecore.xex (0x17000 bytes) (crc32: 0x6f9e8b97 ini: 0x6f9e8b97)
    adding as ximecore.xex at raw offset 0xd57000 len 0x00017000 (end 0x00d6e000)
    extracted nanddump\ximedic.xex (0x90000 bytes) (crc32: 0x1d992bfb ini: 0x1d992bfb)
    adding as ximedic.xex at raw offset 0xd6f000 len 0x00090000 (end 0x00dff000)
    extracted SUPD\ximedic.xexp (0x2800 bytes) (crc32: 0x1a4863a4 ini: 0x1a4863a4)
    adding as ximedic.xexp1 at raw offset 0xe00000 len 0x00002800 (end 0x00e02800)

    ------ adding 5 security files ------

    reading data\crl.bin (0xa00 bytes)
    crl appears crypted, attempting to decrypt with CPU key...failed! Trying alternate key...success!
    adding as crl.bin at raw offset 0xe04000 len 0x00000a00 (end 0x00e04a00)


    reading data\dae.bin (0xad30 bytes)
    dae appears encrypted, attempting to decrypt with CPU key...failed! Attempting to decrypt with alternate key...
    success!
    adding as dae.bin at raw offset 0xe08000 len 0x0000ad30 (end 0x00e12d30)


    reading data\extended.bin (0x4000 bytes)
    adding as extended.bin at raw offset 0xe14000 len 0x00004000 (end 0x00e18000)


    could not read fcrt.bin, using data from previous parse...
    adding as fcrt.bin at raw offset 0xe18000 len 0x00004000 (end 0x00e1c000)


    reading data\secdata.bin (0x400 bytes)
    adding as secdata.bin at raw offset 0xe1c000 len 0x00000400 (end 0x00e1c400)

    ------ checking for Mobile*.dat ------
    MobileB.dat found, adding from previous parse
    adding MobileB.dat as type 0x31 at raw offset 0xe20000 len 0x800 (end 0xe20800)
    MobileC.dat found, adding from previous parse
    adding MobileC.dat as type 0x32 at raw offset 0xe24000 len 0x200 (end 0xe24200)
    MobileD.dat found, adding from previous parse
    adding MobileD.dat as type 0x33 at raw offset 0xe28000 len 0x800 (end 0xe28800)
    MobileE.dat found, adding from previous parse
    adding MobileE.dat as type 0x34 at raw offset 0xe2c000 len 0x800 (end 0xe2c800)
    Statistics.settings found, adding from previous parse
    adding Statistics.settings at raw offset 0xf78000 len 0x1000 (end 0xf79000)

    ------ adding smc_config.bin ------
    adding smc config to offset 0x00f7c000, len 0x400

    ------ finalizing image ------
    Fixing up empty FS block entries...done!
    Writing FS table to image offset 0xe30000 len 0x4000 (end 0xe34000)...done!
    fixing up big block controller on small block NAND LBA numbers...done!
    calculating ECD bytes and assembling raw image...done!
    remapping 2 blocks
    copying 0x4200 bytes of LBA 0x14e to block 0x3fe...zero fill origin...done!
    copying 0x4200 bytes of LBA 0x14e to block 0x3ff...zero fill origin...done!
    done remapping!

    ------ writing image to disk ------
    writing file 'C:\Users\Luca\Desktop\J-Runner\\updflash.bin' to disk...done!
    ---------------------------------------------------------------
    C:\Users\Luca\Desktop\J-Runner\\updflash.bin image built, info:
    ---------------------------------------------------------------
    Kernel : 2.0.17150.0
    Console : Trinity
    NAND size : 16MiB
    Build : Glitch (v2)
    Xell : power on console with console eject button
    Serial : edit
    ConsoleId : edit
    MoboSerial: edit
    Mfg Date : 01/20/2011
    CPU Key : edit
    1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
    DVD Key : edit
    CF LDV : 7
    KV type : type2 (hashed - unchecked, master key not available)
    ---------------------------------------------------------------
    xeBuild Finished. Have a nice day.
    ---------------------------------------------------------------
    Ultima modifica di Babilozzo; 18-05-15 alle 00: 16

  9. #9
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    ovviamente nn chiedevo il permesso , volevo sapere se cerano controindicazioni nel farlo
    questo e' il log comunque.
    cercando su Google ho trovato chi aveva lo stesso problema, e varie soluzioni le ho provate gia. come rimappare, togliere il modulo da 4 gb.creare il freebot con autogg piuttosto con j runner
    ovviamente senza risultato
    Ultima modifica di lucard; 17-05-15 alle 22: 09

  10. #10
    Regular Member
    Data Registrazione
    Dec 2013
    Messaggi
    333
    nel coolrunner D lascia tutti i ponti di stock e usa i fili in dotazione

    se ti si freeza possono essere saldature scadenti
    se metti qualche foto è meglio

  11. #11
    Open Member
    Data Registrazione
    Nov 2012
    Messaggi
    614
    a xell avvenuto il chip si disabilita.
    sicuro di non avere freeze anche da originale?
    provala meglio da originale.
    cosi' ti tiri via il dubbio.

  12. #12
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    da originale va bene. si accende senza problemi , anche xell non freeza, flasho che una meraviglia mai bloccata.
    ma appena provo ad accenderla normale niente.
    i bad block non centrano quindi?di solito se non sono nei primi 50 blocchi non mi hanno mai dato problemi
    comunque anche quando si blocca il chip si disabilita e penso non andrebbe xell
    .
    ovviamente uso tutto originale l unica cosa non ho provato il punto cpu sotto le x clamp
    Ultima modifica di lucard; 18-05-15 alle 17: 33

  13. #13
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    provato con uno squirt 1.2, boot immediati ma si blocca sempre li

  14. #14
    Dolo-miticusss L'avatar di Babilozzo
    Data Registrazione
    May 2012
    Località
    Marmolada, Dolomiti
    Messaggi
    4,279
    Li?? Se te la senti misura le tensioni dei postbit , tutti e otto quando si pianta. Prendi nota della sequenza, puoi avere zero volt oppure un tre volt e qualcosa ma è indifferente, ho hai tensione o non ne hai. Poi spegni e accendi di nuovo e prendi nota, poi riporta la srquenza di postbit per ogni avvio così capiamp dove si pianta esattamente. Oppure ci colleghi un jrpv2 e provi con il rater che è sicuramente meno stressante...
    Ultima modifica di Babilozzo; 18-05-15 alle 21: 59
    Esplora i link spaziali dei Tutorial RGH fatti con le mie manine Sante
    «L'abitudine e' in tutte le cose il miglior maestro.» -- Plinio il vecchio, "Storia naturale"

  15. #15
    DrSchottky
    Guest
    Se sei alla bootanim lo XAM ha già fatto capolino, indi del POST non te ne fai nulla.

  16. #16
    Time to play the Game! I am the debt that can't be paid... You're going down in flames... L'avatar di The Pusher
    Data Registrazione
    Jul 2011
    Messaggi
    8,270
    Senti a me, erasa la nand con il nand programmer che hai e riscrivi freeboot.
    giga.91 and Pa0l0ne like this.

  17. #17
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    provato a dare comando erase 16 mb su sta trinity ma mi da errore su tutti i blocchi
    mentre se scrivo il freebot scrive senza errori

  18. #18
    Membro
    Data Registrazione
    Aug 2011
    Messaggi
    73
    incredibile ma funziona , dato l erase ora va.
    grazie the pusher
    chojin and Pa0l0ne like this.

  19. #19
    Admin L'avatar di Pa0l0ne
    Data Registrazione
    Apr 2013
    Località
    Perugia
    Messaggi
    6,765
    A volte il Pusher mette paura.
    chojin likes this.

Segnalibri

Permessi di Scrittura

  • Tu non puoi inviare nuove discussioni
  • Tu non puoi inviare risposte
  • Tu non puoi inviare allegati
  • Tu non puoi modificare i tuoi messaggi
  •