If you have problem with Geremia Winbond/MXIC unlock Tool or Method, post here

[Raiden]

Detailed photos of the drill hole ?

[Raiden]

nice69, please contact me by email, i can send you privately a slight modified tool made by geremia to solve status problem

[dogged]

Same problem, dvd-drive doesn`t read discs.

[nice69]

[The Pusher]

now you can try with news ixtreme lt 1.91 , that for do an one or one exclusion

[Raiden]

that hole is a bit too much on the right of the perfect spot i think ...

[nice69]

that is a working one

[Raiden]

[nice69]

i have sent you a PM raiden

[niku]

hello a little help over here,

Just unlocked the winbond now i have to flash it with JF ??

Thank you

[nice69]

you can use JF or lizard

[nice69]

status 0x3C first run


status 3C after unlock and powercycle

[niku]

i flashed it and when try to play game it shows as i inserted a DVD VIDEO not a game..any help??

[The Pusher]

i flashed it and when try to play game it shows as i inserted a DVD VIDEO not a game..any help??

If you try to reflash it at stock it's ok?

[wdilbert]

I have same problem that nice69. I have trying to unlock a Liteon 225 WB drive using Geremia's method and JF 1.86. Apparently all went well and I managed to unlock it SPI status = 00. But when it goes to vendor mode the status is 3C and I can't dump the original firmware from drive, keeping stuck "Sending Sector Erase to Port ...". This is the JF log:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.86 Beta (267)
Session Started Sat Aug 06 19:46:12 2011

This is a Wow 64 process running on 4 x 64 bit CPUs 
portio64.sys Driver Installed 
portio64.sys Driver Started, thanks Schtrom ! 
Found 6 I/O Ports.
Found 1 Com Ports.
Found 3 windows drives C: D: K:
Found 0 CD/DVD drives

Sending Vendor Intro to port 0x0170

Serial flash found with Status 0x72

Sending Device ID request to port 0x0170
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Getting Status from port 0x0170
Serial flash found with Status 0x72
Reading Drive Key.
............
Authorised !
Confirming sector 0x3E000.
................
Known f/w confirmed !
Sending Vendor Intro to port 0x0170
Status 0x51
Re-sending Vendor Intro: 
.........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0170
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Updating flash for on-line dump.

Sending Sector Erase to Port 0x0170

Using unlockspi.exe it says drive is SW locked with status 3C. If I say yes to unlock it begins with "do what you have to do now" and immediately, me doing nothing, the protect bits are cleared and device is unlocked with 00 status code. But the next execution of unlockspi.exe enter vendor mode again and says again SPI status 3C.

D:\Temp\0>unlockspi.exe 0170
WinIO initialized and running

Vendormode entered
SPI device ID = EF 30 12   Winbond

SPI status register = 3C
SW locked !!
Do you want to continue unlocking? y/n y
SPI status register = 3C
Sound test...


Do what you have to do NOW!

Protect bits cleared !!
Wait a few to be sure
SPI device ID = EF 30 12
SPI status register = 00
!!! UNLOCKED !!!!

D:\Temp\0>

Finally I managed to read the flash combining the use of JF to read, unlockspi.exe to enter vendor mode and the russian program unlock_16d4s to unlock spi state to 00, but when I write the firmware then JF always says "write verification failed" and the games do not start (play dvd). If I try to write back to stock firmware it's the same: write verification failed.

Any idea?

[The Pusher]

try to send only writekey from jungleflasher

[nice69]

[wdilbert]

try to send only writekey from jungleflasher

Stage 1, Complete!
Failed at Stage 2

[aboalsos]

hi

i unlocked my winbond and write great , but i got the ejct problem and i fix it by this [URL="http://www.consoleopen.com/forum/tutorial-modchip-e-hardware-xbox-360-xbox360-slim/357-eject-fix-after-winbond-unlock.html"]tut [/URL], now the desk doesn't spin please i need any Solution?? it's 4 day ago i tray and tray >....

[Electron^-]

Do you have fixed the eject problem but now the drive don't read disk? If it don't spin up of if xbox give you "play DVD", it could be related by an too deep cut... there aren't a fix for now...

Sent from my Nexus S using Tapatalk